Synthesis and thermophysical properties of RETa3O9 (RE = Ce,Nd, Sm,Eu, Gd,Dy, Er) as promising thermal barrier coatings

Thermal barrier coatings (TBCs) are one of the most important materials in gas turbine to protect the high temperature components. RETa₃O₉ compounds have a defect‐perovskite structure, indicating that they have low thermal conductivity, which is the critical property of TBCs. Herein, dense RETa₃O₉ bulk ceramics were fabricated via solid‐state reaction. The crystal structure was characterized by X‐ray diffraction (XRD) and Raman Spectroscope. Scanning electron microscope (SEM) was used to observe the microstructure. The thermophysical properties of RETa₃O₉ were studied systematically, including specific heat, thermal diffusivity, thermal conductivity, thermal expansion coefficients, and high‐temperature phase stability. The thermal conductivities of RETa₃O₉ are very low (1.33‐2.37 W/m·K, 373‐1073 K), which are much lower than YSZ and La₂Zr₂O₇; and the thermal expansion coefficients range from 4.0 × 10^?6 K^?1 to 10.2×10^?6 K^?1 (1273 K), which is close to La₂Zr₂O₇ and YSZ. According to the differential scanning calorimetry (DSC) curve there is not phase transition at the test temperature. Due to the high melting point and excellent high‐temperature phase stability with these oxides, RETa₃O₉ ceramics were promising candidate materials for TBCs.     

Preparation and the controlled release effect study of graphene oxide-modified poly(ε-caprolactone)

Functionalized graphene oxide-modified poly(ε-caprolactone) composites ((graphene oxide)GO/PCL) were successfully synthesized by Steglich esterification for drug applications of controlled release. Lomefloxacin (LMF) was selected as a model drug to investigate its controlled release properties. The controlled release effect of the LMF-contained pills of the GO/PCL and polylactic acid blend was evaluated. In contrast to the pure PCL, GO/PCL could effectively adjust the time of drug release and release the drug at a constant rate, achieving the controlled release requirements. Furthermore, different additive amounts of graphene oxide have different effects on adjusting the time of controlled release, while the best result obtained under the ratio is 4% GO/PCL as carrier of drug. Thus, high-quality drug carrier materials are obtained which are more suitable for clinical use. Exploring the optimum addition of graphene oxide is very significant for the development of GO/PCL carrier material.     

Identification of factors that accelerate hydrogen production by Clostridium butyricum RAK25832 using casamino acids as a nitrogen source

The ability of Clostridium butyricum RAK25832 to use casamino acids as a nitrogen source was investigated. Strain RAK25832 showed the capacity to utilize different types of carbon sources. With glucose as a carbon source (10 g/L), the preferred final concentration of casamino acids was 26.67 g/L, with a cumulative hydrogen production, production rate, and yield of 2505 mL H₂/L, 160 mL/h, and 1.81 mol H₂/mol glucose, respectively. Eighteen metal elements were screened to identify the most important metals for biohydrogen production, and four elements were optimized. The optimal medium composition was MgCl₂·6H₂O (0.1 g/L), K₂HPO₄·3H₂O (6.67 g/L), NaHCO₃ (2.6 g/L), and FeCl₂·4H₂O (0.002 g/L). Vitamin supplementation of the medium showed no significant effect on hydrogen production. Under the optimized conditions, cumulative hydrogen production reached 3074 mL H₂/L. This is the first study to demonstrate the use of casamino acids as a nitrogen source by C. butyricum.     

Robust model for optimization of forming process for metallic bipolar plates of cleaner energy production system

Energy production systems such as proton-exchange membrane fuel cell (PEMFC) has a promising future in the cleaner energy market due to zero emissions. Rubber pad forming (RPF) process of metallic bipolar plates of PEMFCs is gaining attention among the researchers. Studies based on design of experiments have been conducted to find the crucial parameters of the forming process. These methods are based on the assumptions of the model structure, correlated residuals, etc., which can cause uncertainty in estimation ability of the model on unseen data. Therefore, the present study focuses on the design of robust models of these parameters for PEMFCs using an optimization approach of genetic programming (GP). The inputs from the experiments considered in GP are radius, the friction coefficient, the filling factor and the minimum thickness. Experiments on PEMFCs validates the performance of the GP models. Further, the relationships between the two inputs and the three outputs for PEMFCs are generated as well as the contributions of each input to each of the output. Optimization of the models generated by GP can further determine the forming quality of metallic bipolar plates of PEMFCs by an appropriate setting of the two inputs.     

Research on the hot surface ignition of hydrogen‐air mixture under different influencing factors

To further reveal the pre‐ignition characteristics of hydrogen internal combustion engine, the effect of hot surface characteristic parameters on the ignition characteristics of hydrogen‐air mixture was investigated in this research. Based on the prototype of the constant volume combustion bomb with an overhead glow plug, the duration from the heating of the hot surface to the combustion of hydrogen‐air mixture, the so‐called heating duration, was firstly researched under different fuel‐air equivalence ratio, initial temperature, initial pressure, hot surface temperature, and hot surface area, and the influence of each factor on the heating duration was analyzed. The results show that the order of the effect of each factor on the hot surface ignition is as follows: hot surface temperature > initial pressure of hydrogen‐air mixture > equivalent ratio > initial temperature of hydrogen‐air mixture > hot surface area. The influence of the hot surface characteristic parameters on the heating duration was further analyzed in detail. On this basis, the relationship among the critical ignition temperature, the heating duration and the hot surface area was researched and established. The results show that the heating duration is the only major factor affecting the critical ignition temperature. Finally, the research results were applied to analysis the pre‐ignition in hydrogen internal combustion engine.     

土壤硝酸盐中15N同位素测定前处理自动化辅助装置设计和验证

随着稳定同位素质谱技术在土壤氮循环研究中的广泛应用,氮稳定同位素分析对样品前处理方法提出了更高要求,而合适的样品处理方法是确保分析结果准确可靠的关键。设计开发1种适用于土壤微量硝酸盐中氮稳定同位素分析前处理辅助装置,将基于光电感应装置的自动进样系统与注液、抽真空-气体置换系统相融合,将原前处理方法中液体试剂注入,反应体系抽真空及氦气置换等人为操作过程改为自动化处理环节。系统测试结果表明:该套辅助装置具有良好的自动抽真空、注气和加液重复性。装置抽真空系统的真空度绝对误差可控制在0.5 Pa以内,气体注入体积绝对误差可控制在0.2 mL以内,而注液系统的注液体积绝对误差也可控制在0.1 mL以内,变异系数(CV)均小于1%。使用标准参比样品测试整套系统的准确度和精密度,所有测试样品均获得了较好的准确度和精密度,CV<1%。研制的装置结合痕量气体预浓缩装置—稳定同位素质谱(PreCon-IRMS)联用仪,可以建立方便快捷的低样品量下硝酸盐中15 N同位素质谱检测方法,可为土壤氮循环过程研究提供关键技术支撑。     

Characterizing physical habitat preferences and thermal refuge occupancy of brook trout (Salvelinus fontinalis) and Atlantic salmon (Salmo salar) at high river temperatures

Anthropogenic influences, including climate change, are increasing river temperatures in northern and temperate regions and threatening the thermal habitats of native salmonids. When river temperatures exceed the tolerance levels of brook trout and Atlantic salmon, individuals exhibit behavioural thermoregulation by seeking out cold‐water refugia – often created by tributaries and groundwater discharge. Thermal infrared (TIR) imagery was used to map cold‐water anomalies along a 53 km reach of the Cains River, New Brunswick. Trout and salmon parr did not use all identified thermal anomalies as refugia during higher river temperature periods (>21°C). Most small‐bodied trout (8–30 cm) were observed in 80% of the thermal anomalies sampled. Large‐bodied trout (>35 cm) required a more specific set of physical habitat conditions for suitable refugia, that is, 100% of observed large trout used 30% of the anomalies sampled and required water depths >65 cm within or adjacent to the anomaly. Densities of trout were significantly higher within anomalies compared with areas of ambient river temperature. Salmon parr were less aligned with thermal anomalies at the observed temperatures, that is, 59% were found in 65% of the sampled anomalies; and densities were not significantly different within/ outside anomalies. Salmon parr appeared to aggregate at 27°C, and after several events over 27°C variability in aggregation behaviour was observed – some fish aggregated at 25°C, others did not. We stipulate this is due to variances of thermal fatigue. Habitat suitability curves were developed for velocity, temperature, depth, substrate, and deep water availability to characterize conditions preferred by fish during high‐temperature events. These findings are useful for managers as our climate warms, and can potentially be used as a tool to help conserve and enhance thermal refugia for brook trout and Atlantic salmon in similar systems.     

Recovery of Collided RFID Tags With Frequency Drift on Physical Layer

In a passive ultra-high frequency (UHF) radio frequency identification (RFID) system, the recovery of collided tag signals on a physical layer can enhance identification efficiency. However, frequency drift is very common in UHF RFID systems, and will have an influence on the recovery on the physical layer. To address the problem of recovery with the frequency drift, this paper adopts a radial basis function (RBF) network to separate the collision signals, and decode the signals via FM0 to recovery collided RFID tags. Numerical results show that the method in this paper has better performance of symbol error rate (SER) and separation efficiency compared to conventional methods when frequency drift occurs.      

Viability of intertwined supply networks: extending the supply chain resilience angles towards survivability. A position paper motivated by COVID-19 outbreak

An intertwined supply network (ISN) is an entirety of interconnected supply chains (SC) which, in their integrity secure the provision of society and markets with goods and services. The ISNs are open systems with structural dynamics since the firms may exhibit multiple behaviours by changing the buyer-supplier roles in interconnected or even competing SCs. From the positions of resilience, the ISNs as a whole provide services to society (e.g. food service, mobility service or communication service) which are required to ensure a long-term survival. The analysis of survivability at the level of ISN requires a consideration at a large scale as resilience of individual SCs. The recent example of coronavirus COVID-19 outbreak clearly shows the necessity of this new perspective. Our study introduces a new angle in SC resilience research when a resistance to extraordinary disruptions needs to be considered at the scale of viability. We elaborate on the integrity of the ISN and viability. The contribution of our position study lies in a conceptualisation of a novel decision-making environment of ISN viability. We illustrate the viability formation through a dynamic game-theoretic modelling of a biological system that resembles the ISN. We discuss some future research areas.     

电子束诱导沉积钴微米线及其铁磁性

通过电子束诱导沉积的方法制备了钴(Co)微米线,并利用扫描电子显微镜(SEM)、原子力/磁力显微镜(AFM/MFM)以及物性测量系统(PPMS)等手段对Co微米线的沉积尺寸、微结构、铁磁性和电学性质进行了测试和分析。研究结果表明:Co微米线轮廓清晰、均匀性好。在不同的沉积条件下,微米线的实际长度与设定长度基本一致;实际宽度数据呈类梯形分布,半高宽是设定值的2~10倍;实际厚度低于设定厚度的60%。沉积电流对Co微米线的铁磁特性有重要影响。当沉积电流大于0.5 nA时,样品呈现出良好的铁磁特性。另外,电学性能测试结果显示Co微米线呈现绝缘特性。成功制备了室温铁磁绝缘Co微米线,这将有助于深入开展微纳尺度的结构与器件的研究和应用。